BS/EN 13598-2-2020 pdf download

07-21-2021 comment

BS/EN 13598-2-2020 pdf download.Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vlnyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for manholes and inspection chambers.
EN 68 1-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers
EN 68 1-3, Elastomeric seals — Materials requirements for pipe Joint seals used in water and drainage applications — Part 3: Cellular materials of vulcanized rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage — Un plasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
EN 1905, Plastics piping systems — Un plasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material — Met hod for assessment of the PVC content based on total chlorine content
EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of volatile content
EN 12666-1. Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
EN 13101:2002, Steps for underground man entry chambers — Requirements, marking, testing and evaluation of conformity
EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unpiasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE) — Part 2: Specifications for pipes and fittings with smooth internal and
external surface and the system, Type A
EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized polyfrmnyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PB) — Part 3: Specifications for pipes and fittings with smooth internal and
profiled external surface and the system, Type B
EN 14396, Fixed ladders for manholes
EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes.
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126)
EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the- clock method (ISO 3127)
EN ISO 345 1-1, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1)
EN ISO 3451-5, Plastics — Determination of ash — PartS: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 9967:2016, Thermoplastics pipes — Determination of creep ratio (ISO 9967:2016)
EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of
oxidation induction time (isothermal 017’) and oxidation induction temperature (dynamic OIT)
(ISO 1135 7-6)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized polyfrmnyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value
(ISO 13229)
EN ISO 13254, Thermo plastics piping systems for non-pressure applications — Test method for watertightness (ISO 13254)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test met hod for Ieaktightness of elastomeric sealing ring type joints (ISO 13259)
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for impact strength (ISO 13263)
ISO 13266:2010, Thermoplastics piping systems for non-pressure underground drainage and
sewerage — The rmo plastics shafts or risers for inspection chambers and manholes — Determination of resistance against surface and traffic loading (iSO 13266)
ISO 13267, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermo plastics inspection chamber and manhole bases — Test methods for buckling resistance (ISO 13267)
ISO 13268, Thermoplastics piping systems for non-pressure underground drainage and sewerage — Therino plastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness
For the purposes of this document, the terms, definitions and abbreviations given in EN ISO 1043- 1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropcdia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
man hole
chamber with a removable cover constructed in a drain or sewer to permit entry by personnel, with a riser of 800 mm minimum inner diameter
Note 1 to entry: Figure 1 shows typical manholes.
Note 2 to entry: See EN 476 for dimensions of non-circular manholes.
Note 3 to entry: Manholes are subject to national safety regulations and / or local provisions regarding man-entry limitations.
3.2
inspection chamber
chamber with a removable cover constructed in a drain or sewer that permits the introduction of cleaning and inspection equipment from surface level, but does not provide access for personnel, with a riser of 200 mm minimum outer diameter and an inner diameter of less than 800 mm
Note 1 to entry: Figure 2 shows typical inspection chambers.
Note 2 to entry: See EN 476 for non-circular chambers.
3.3
base
bottom part of a manhole or inspection chamber, allowing direct connection to buried drain or sewer pipes and including integrally formed channels with benching as appropriate
Note 1 to entry: In case of a one-piece manhole or inspection chamber, for testing purposes the base component ends at a distance of minimum 300 mm measured from the top of the main channel. Above 300 mm the section should be considered as a riser and tested accordingly.
Note 2 to entry: Bases having a spherical design may be used. National regulations can apply.BS/EN 13598-2-2020 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
BS EN 12607-3-2000 pdf download BS Standards

BS EN 12607-3-2000 pdf download

BS EN 12607-3-2000 pdf download.Methods of test for petroleum and its products — BS 2000-460.3: Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 3: RFT...
Read More
EN 12329-2000 pdf download BS Standards

EN 12329-2000 pdf download

BS EN 12329-2000 pdf download.Corrosion protection of metals — Electrodeposited coatings of zinc with supplementary treatment on iron or steel. This BS EN 12329 specifies requirements for electrodeposited coatings of zinc on iron or steel witt supplementary...
Read More
BS EN 1430-2000 pdf download BS Standards

BS EN 1430-2000 pdf download

BS EN 1430-2000 pdf download.Methods of test for petroleum and its products — BS 2000-292:Bitumen and bituminous binders — Determination of particle polarity of bitumen emulsions (Identical with IP 292-2000). This BS EN 1430 specifies a method...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information