BS EN 14364-2013 pdf download.Plastics piping systems for drainage and sewerage with or without pressure Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) Specifications for pipes, fittings and joints.
2 Normative references
The following documents, in whole or in part. are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 681-1, Elastomeric seals — Materials requirements for pe joint seals used in water and drainage applications — Part 1: Vulcanized rubber
EN 1119. Plastics piping systems — Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings
— Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
EN 1447, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of long-term resistance to internal pressure
CEN/TS 14578, Plastics piping systems for water suppty or drainage or sewerage — Glass reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) — Recommended practice for installation
CEN/TS 14632, Plastics piping systems for drainage, sewerage arid water supply, pressure and non-pressure
— Glass reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Guidance for the assessment of conformity
CEN/TS 14807, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Guidance for the structural analysis of buried GRP-UP pipelines
EN ISO 75-2:2004, Plastics — Determination of temperature of deflection under load — Part 2: Plastics, ebonite and long-fibre-reinforced composites (ISO 75-2:2004)
EN ISO 527-4, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthatopic fibre-reinforced plastic composites (ISO 527-4)
EN ISO 527-5, Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre- rein forced plastic composites (ISO 52 7-5)
EN ISO 1452-3, Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 3: Fittings (ISO 1452-3)
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126) ISO 2531, Ductile iron pipes, fittings, accessories and their joints for water applications
Iso 4200, Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
ISO 7432, Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
ISO 7685, Plastics piping systems — Glass-reinforced themiosetting plastics (GRP) pipes — Determination of initial specific ring stiffness
ISO 8483, Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of bolted flange joints
ISO 8513, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of longitudinal tensile properties
BS EN 14364:2013
EN 14364:2013 (E)
ISO 8521, Plastic piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the apparent initial circumferential tensile strength
ISO 8533, Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints
ISO/TR 10465-3, Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) — Part 3 Installation parameters and application limits
ISO 10466, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test method to prove the resistance to initial ring deflection
ISO 10468. Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and the calculation of the wet creep factor
ISO 10471, Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and long-term ultimate relative ring deflection under wet conditions
ISO 10928. Plastics piping systems — Glass reinforced thermosetting plastics (GRP) pipes and fittings — Methods l& regression analysis and their use
ISO 10952, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack from the inside ole section in a deflected condition
Iso 11922-1, Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1:
Metric series
3 Terms, definitions and symbols
For the purposes of this document, the following terms, definitions and symbols apply.
nominal size
DN
aiphanumerical designation of size of component, which is a convenient integer approximately equal to a manufacturing dimension in mm and which can apply to either the internal diameter (UN-ID) or the external diameter (DN-OD)
Note 1 to entry: The designation for reference or marking purposes consists of the letters DN-ID or DN-OD plus a number.
3.2
nominal stiffness
SN
aiphanumerical designation for stiffness classification purposes, which has the same numerical value as the
minimum initial specific ring stiffness value required, when expressed in Newtons per square metre (N/rn2)
Note ito entry: The designation for reference or marking purposes consists of the letters SN plus a number. (See 4.1.4.)
3.3
specific ring stiffness
S
physical characteristic of the pipe, expressed in Newtons per square metre (N/rn2) which is a measure of the resistance to ring deflection per metre length under external load and is defined by Formula (1):BS EN 14364-2013 pdf download.