BS EN 60534-3-2-2001 pdf download

08-14-2021 comment

BS EN 60534-3-2-2001 pdf download.Industrial-process control valves Part 3-2: Dimensions — Face-to-face dimensions for rotary control valves except butterfly valves.
This part of lEG 60534 applies to the following control valves:
— types: segmented ball and eccentric rotary control valves with or without flanges;
— nominal sizes: DN2O up to and including DN400;
NOTE 1 See ISO 7005 and ISO 6708.
— designations: PN1O, PN16. PN2O, PN25. PN4O. PN5O. PN63, PNIOO and PN11O.
NOTE 2 See ISO 7005 and ISO 7268.
NOTE 3 Designations PN63 and PNIOO are not included In ISO 7005.
NOTE 4 Designations PN2O, PN5O and PN1 10 are not included in European Standard EN 1092,
NOTE 5 For the purposes of face-to-f ace dimensions, designation PN100 in EN 1092 corresponds to PN1IO.
NOTE 6 For the purposes of face-to-face dimensions, the following correlations apply
— PN2O covers Classes 125 and 150 In the ANSI system:
— PN5O covers Classes 250 and 300 in the ANSI system;
— PN1 10 covers Class 600 in the ANSI system.
Only raised face flanges are covered.
Specifically excluded from this standard are all valves having welded or threaded end connections.
2 NormatIve references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of lEG 60534. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 60534 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards.
lEG 60534 (all parts), Industrial-process control valves
ISO 6708. Pipework components — Definition and selection of ON (nominal size)
ISO 7005 (all parts), Metallic flanges
ISO 7268. Pipe components — Definition of nominal pressure
EN 1092 (all parts), Flanges and their joints
3 Definitions
For the purposes of this part of IEC 60534. the definitions in the other parts of IEC 60534 apply with the addition of the following.
tiangeless control valve
control valve having no line flanges but intended to be installed by clamping between pipe flanges
4 Dimensions
Dimensions given In table 1 are the overall lengths of the listed valves. See figure 1 for a pictorial explanation of dimensions.
They do not include any allowances for gaskets to seal the joints between the valve ends and the pipeline flanges.BS EN 60534-3-2-2001 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
BS EN 12607-3-2000 pdf download BS Standards

BS EN 12607-3-2000 pdf download

BS EN 12607-3-2000 pdf download.Methods of test for petroleum and its products — BS 2000-460.3: Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 3: RFT...
Read More
BS EN 12329-2000 pdf download BS Standards

BS EN 12329-2000 pdf download

BS EN 12329-2000 pdf download.Corrosion protection of metals — Electrodeposited coatings of zinc with supplementary treatment on iron or steel. This BS EN 12329 specifies requirements for electrodeposited coatings of zinc on iron or steel witt supplementary...
Read More
BS EN 1430-2000 pdf download BS Standards

BS EN 1430-2000 pdf download

BS EN 1430-2000 pdf download.Methods of test for petroleum and its products — BS 2000-292:Bitumen and bituminous binders — Determination of particle polarity of bitumen emulsions (Identical with IP 292-2000). This BS EN 1430 specifies a method...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information