BS ISO 14743:2020 pdf download

01-01-2021 comment

BS ISO 14743:2020 pdf download.Pneumatic fluid power – Push-in connectors for thermoplastic tubes.
In pneumatic fluid power systems, power is transmitted and controlled through air under pressure within a circuit.
Components are connected through their ports by means of connectors (fittings) and conductors.
BS ISO 14743:2020 specifies the general requirements and test methods for the design and performance of push-in connectors for use with thermoplastic tubes with outside diameters (OD) from 3 mm to 16 mm including dimensions in inches.
BS ISO 14743:2020 is intended to establish uniform methods of testing complete push-in connector assemblies as used in pneumatic fluid power applications. It is not applicable to air braking systems.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7-1, Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation.
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 5598, Fluid power systems and components — Vocabulary.
ISO 8573-1:2010, Compressed air — Part 1: Contaminants and purity classes.
ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1:
Bending tests at ambient temperature.
ISO 16030, Pneumatic fluid power — Connections — Ports and stud ends.
ANSI/ASME B 1.1, Unified Inch Screw Threads, (UN and UNR Thread Form).
ANSI/ASME B 1.20.1, Pipe Threads, General Purpose, Inch.
ANSI/ASME B1.20.3, Dryseal Pipe Threads (Inch).
7 Design
7.1 Push-in connector dimensions shown in Figures 2 to 2 shall conform to the dimensions given in Tables 1 to7.
7.2 Hexagon tolerances across flats shall be in accordance with Iso 4759-1, Grade C. The minimum hexagon across-corner turn diameter of 1,092 times the normal across flats dimension shall be used.
7.3 For connectors with the thread M and G, thread and stud end shall be in accordance with ISO 16030. For connector with the thread R, thread and stud end shall be in accordance with ISO 7-1.BS ISO 14743:2020 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
BS EN 12607-3-2000 pdf download BS Standards

BS EN 12607-3-2000 pdf download

BS EN 12607-3-2000 pdf download.Methods of test for petroleum and its products — BS 2000-460.3: Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 3: RFT...
Read More
EN 12329-2000 pdf download BS Standards

EN 12329-2000 pdf download

BS EN 12329-2000 pdf download.Corrosion protection of metals — Electrodeposited coatings of zinc with supplementary treatment on iron or steel. This BS EN 12329 specifies requirements for electrodeposited coatings of zinc on iron or steel witt supplementary...
Read More
BS EN 1430-2000 pdf download BS Standards

BS EN 1430-2000 pdf download

BS EN 1430-2000 pdf download.Methods of test for petroleum and its products — BS 2000-292:Bitumen and bituminous binders — Determination of particle polarity of bitumen emulsions (Identical with IP 292-2000). This BS EN 1430 specifies a method...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information