API 613:2003 pdf download

12-19-2022 comment

API 613:2003 pdf download.Special Purpose Gear Units for Petroleum, Chemical and Gas Industry Services
1.1 SCOPE
This standard covers the minimum requirements for spe- cial-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallel- shaft design for petroleum, chemical and gas industry ser- vices. This standard is primarily intended for gear units that are in continuous service without installed spare equipment. Gear sets furnished to this standard shall be considered matched sets. Note: The purchase of a spare set of gear rotors or a complete gear unit does not mean that the equipment is spared. This standard includes related lubricating systems, con- trols, instrumentation, and other auxiliary equipment. This standard is not intended to apply to gear units in general-pur- pose service, which are covered by API Std 677; to gears inte- gral with other equipment, such as integrally geared compressors covered by Std 617 or Std 672; or to gears other than helical. Note: A bullet ( . ) at the beginning of a paragraph indicates that either a decision is required or further information is to be provided by the purchaser. This information should be indicated on the data sheets (see Appendix A); otherwise, it should be stated in the quota- tion request or in the order.
1.5 DEFINITION OF TERMS
Terms used in this standard are defined in 1.5.1 through 1.5.38. 1.5.1 axially (horizontally) split refers to casing joints that are parallel to the shaft centerline. 1.5.2 The bending stress number (S) corresponds to the likelihood of fatigue cracking at the tooth root filet. If this stress is excessive, it may lead to failure of the gear teeth. 1.5.3 critical speed is a shaft rotational speed at which the rotor bearing support system is in a state of resonance (see 2.6.1). 1.5.4 The use of the word design in any term (such as design horsepower, design pressure, design temperature, or design speed) should be avoided in the purchaser’s specifica- tions. This terminology should be used only by the equipment designer and the manufacturer. 1.5.5 gauss levels refers to the magnetic field level of a component measured with a “Hall effect” probe, with no interference from adjacent magnetic part or structures. 1.5.6 gear refers to either the pinion or the gear wheel. 1.5.7 The gear service factor (SF) is the factor that is applied to the tooth pitting index and the bending stress number, depending on the characteristics of the driver and the driven equipment, to account for differences in potential overload, shock load, and/or continuous oscillatory torque characteristics. 1.5.8 gear unit is the complete power transmission assembly including the housing, gears, and bearings. 1.5.9 gear unit rated power is the maximum power specified by the purchaser on the data sheet and stamped on the nameplate (see 2.2.1). 1.5.10 gear wheel (bull gear) refers to the lowest speed rotor.

                                           Related Information                                             Download
PS:Thank you for your support!
API TR 10TR2:1997(R2002) pdf download API Standards

API TR 10TR2:1997(R2002) pdf download

API TR 10TR2:1997(R2002) pdf download.Shrinkage and Expansion in Oilwell Cements 4.1.1 Some equipment measures the external volume change. Other equipment measures the volume of fluid intake or expulsion during the hydration. Measurement of V, and y must...
Read More
API Std 1104:2005 pdf download API Standards

API Std 1104:2005 pdf download

API Std 1104:2005 pdf download.Welding of Pipelines and Related Facilities 1.1 SCOPE This standard covers the gas and arc welding of butt, fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping,...
Read More
API STD 613:2003 pdf download API Standards

API STD 613:2003 pdf download

API STD 613:2003 pdf download.Special Purpose Gear Units for Petroleum, Chemical and Gas Industry Services 1.1 SCOPE This standard covers the minimum requirements for spe- cial-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information