ASME B30.25:2007 pdf download

12-17-2022 comment

ASME B30.25:2007 pdf download Scrap and Material Handlers
SECTION Il: SCOPE EXCLUSIONS
The B30 Standard does not apply to track and automotive jacks, railway or automobile wrecking cranes, shipboard cranes,shipboard cargo-handling equipment,well-drilling derricks, skip hoists, mine hoists, truckbody hoists, car or barge pullers, conveyors, excavatingequipment,or equipment covered under the scope ofthe following standards: A10A17A90,A92A120,B20B56,and B77.
SECTION IIl: PURPOSE
The B30 Standard is intended to
(a) prevent or minimize injury to workers, and other-wise provide for the protection oflife, limb, and propertyby prescribing safety requirements(b) provide direction to manufacturers, ownersemployers, users, and others concerned with, or respon-sible for, its application(c) guide governments and other regulatory bodiesin the development, promulgation, and enforcement ofappropriate safety directives
SECTION IV: USE BY REGULATORY AGENCIES
These Volumes may be adopted in whole or in partfor governmental or regulatory use. If adopted for governmental use, the references to other national codesand standards in the specific volumes may be changedto refer to the corresponding regulations of the governmental authorities.
SECTION V: EFFECTIVE DATE
(a) Effective Date. The effective date of this Volume ofthe B30 Standard shall be 1 vear after its date ofissuanceConstruction,installation, inspection, testing, maintenance, and operation of equipment manufactured and facilities constructed after the effective date of this Vol-ume shall conform to the mandatory requirements ofthis Volume.
(b) Existing Installations. Equipment manufacturedand facilities constructed prior to the effective date ofthis Volume of the B30 Standard shall be subject to theinspection, testing, maintenance, and operation requirements of this Standard after the effective date.
It is not the intent of this Volume of the B30 Standardto require retrofitting of existing equipment. Howeverwhen an item is being modified, its performance requirements shall be reviewed relative to the requirementswithin the current volume. The need to meet the currentrequirements shall be evaluated by a qualified personselected by the owner (user). Recommended changesshall be made by the owner (user) within 1 year.
SECTION VI:REQUIREMENTS ANDRECOMMENDATIONS
Requirements of this Standard are characterized byuse of the word shall. Recommendations of this Standardare characterized by the word should.
SECTION VIl: USE OF MEASUREMENT UNITS
This Standard contains SI (metric) units as well asU.S. Customary units. The values stated in customaryunits are to be regarded as the standard. The SI unitsare a direct (soft) conversion from the customary units.
SECTION VIIl: REQUESTS FOR REVISION
The B30 Standards Committee will consider requestsfor revision of any of the volumes within the B30 Stan-dard. Such requests should be directed to:
Secretary,B30 Standards CommitteeASME Codes and Standards
Three Park Avenue
New YorkNY 10016-5990
The requests should be in the following format:Volume:Cite the designation and title of the volumeEdition:Cite the applicable edition of the volumeCite the applicable paragraph number(s)and the relevant heading(s).
Subject:
Request:Indicate the suggested revision.
State the rationale for the suggestedRationale:revision.

                                           Related Information                                             Download
PS:Thank you for your support!
ASME B107.100:2002 pdf download ASME Standards

ASME B107.100:2002 pdf download

ASME B107.100:2002 pdf download WKENGHLD INCORPORATING ASME B107.6, ASME B107.9, ASME B107.39, and ASME B107.40 4.5 Proof Torque When tested as specified, wrenches shall withstand the proof torque specified in the applicable tables without failure or permanent...
Read More
ASME BPE:2002 pdf download ASME Standards

ASME BPE:2002 pdf download

ASME BPE:2002 pdf download BIOPROCESSING EOUIPMENT GR-1 INTRODUCTION This Standard provides the requirements applicableto the design of bioprocessing equipment inciudingaspects related to sterilily and cleanability,dimensionsand tolcranccs, surfacc finish, material joining, andscals. Thcsc apply to: (a) componcnts that...
Read More
ASME N509:2002 pdf download ASME Standards

ASME N509:2002 pdf download

ASME N509:2002 pdf download NUCLEAR POWER PLANT UNITS AID CDMPONENTS 1 SCOPE This Standard covers requirements for the designconstruction, and qualification and acceptance testingof the air-cleaning units and components which makeup Engineered Safety Feature (ESF) and other...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information